See our newest Products.
New Cable Workshop Surge Generator
Adret SG80034 - Surge Generator
Morné Steffens Senior Production Manager at Adret, South Africa talks though the features and functions of the Adret SG80034 - Surge Generator
Updated Cable Identifier
Adret Ci75 Cable Identifier
Morné Steffens Senior Production Manager at Adret, South Africa talks though the features and functions of the Adret Ci75 Cable Identifier.
Surge Generator - Adret SG80034
-
Surge Generator
Output Voltage: 7.5, 17, 34kV 1450 Joule (Ws)
Pulse Rate: Every 4 Seconds (15PPM)
Mains Condition Lockout System
Checks Mains input High
Checks Mains Input Low
Checks Mains Polarity Correct
Checks Earthing Integrity
-
34KV 1450 Joule Mining Cable Shop Surge Generator
New stainless steel enclosure
10 earth leads
Additional milliamp reading
Cabinet has wheels for easy transport
Perspex cover lid for protection
-
-
Designed for Australian conditions
-
Delivery time 4-6 weeks
Cable Repair Tapes
-
-
PCP 0.64mm x 25mm x 0.5kg
PCP 0.64mm x 50mm x 1.0kg
CSP - Yellow - 0.64mm x 50mm x 1.0kg
CSP - Red - 0.64mm x 50mm x 1.0kg
CSP - Green - 0.64mm x 50mm x 1.0kg
EPR - Flame resistant EPR
PCP semi con (25mm)
PCP semi con (50mm) -
Designed for Australian conditions.
-
Stock on hand
Special order delivery time 4-6 weeks
Cable Vulcanizer
-
Cable Vulcanizers are used to bake the rubber in and around the cable. Essential for all repairs and cable joints/splices.
-
Suitable for cable sizes from:
10mm-80mm diameter cable
-
Designed and built in Australia.
-
Made to order
Delivery time 4-6 weeks
Symmetrical Load Tester
-
A Symmetrical Load Tester is an important device used to test that repaired 3 phase trailing cables are operating electrically symmetrical. Australian Standards require all mining cables pass this test before returning to service.
-
15 or 20 KVA - 3 Phase transformer
415 Volt Primary to 31 Volt Secondary @ a maximum load of 385 Amps output
Variac 3 Phase - Maximum load 28Amps
Diris A-30 Power Meter - Which reads the three individual phase currents.
3 x Current Transformers (ratio 500/5)
1 x Milliamp Meter - Which reads the milliamp leakage injected into the earth conductors.
Timers designed for 30 seconds (30 sec on) operation time and 2 minutes cool down time (2min off).
Emergency Stop Button
Run Button
Power on keyed Button
3 x 5 metres of test leads
120mm² single core cable
10 metres of main lead - 20Amp 4 pin plug
Unit comes in a powder coated 1.5mm Galvabond (IP21) steel enclosure
Wheels: fixed and swivel (with break) wheels
Custom connecting pins to suit cables under test (to be advised by customer)
Total size: 1600mm x 600mm x 850mm
Total weight: 320kg
-
Designed and built in Australia.
-
Download the PDF manual
-
Made to order
8-10 weeks
Partial Break Hammer
-
The Partial Break Hammer physically manipulates the cable while tests are conducted with the Partial Break Testing unit. The cable is drawn through the unit (in the same way as it is with the cable handler) with an additional mechanical agitation. This allows the test to detect faults that would otherwise be undetected when the cable is laid flat.
-
1.5KW 415V Motor coupled to a flange mounted gearbox with a 10:1 reduction
Rotating hammer is driven by 0.75kW 415V motor and Vee belt drive
Adjustable pressure rollers
Foward/Reverse/stop control
10m flexible rubber power lead with 20Amp four pin plug
Tool shelf
Emergency Stop
-
18mm-85mm cable diameter
-
To be advised by client
-
Designed and built in Australia.
-
made to order
4-6 week
Cable Drum Roller - Large
-
Used to wind cables back on and off cable drums
-
GANDA Drum Roller (Large)
Take drums up to 2400mm wide
Fabricated frame with fork pockets
Plain steel rollers and bearings
10m of hoses and quick connect couplings and fittings
Remote control & transmitter with proportional button and Estop
2 x 400cc hydraulic motors
60l of hydraulic oil (supplied)
15m of electrical cable and 20 Amp plug.
Hydraulic system:
Power unit 75 ltr tank 7.5 kw with proportional flow.Powerpack has inside fabricated frame with forklift pockets and lifting points and quick release holes.
-
Colour to be advised by client
-
Designed and built in Australia.
-
Download PDF manual
-
Made to order
8-10 weeks
Test Pins
-
Case Hardened Steel Test Pins.
Each pin is calibrated with sticker.
Precision made and calibrated
Pins come with foam protected Pelican Case.
-
Seven (7) pins sizes:
6.32 dia pin
7.90 dia pin
9.50 dia pin
11.07 dia pin
12.67 dia pin
15.85 dia pin
19.02 dia pin
-
Designed and built in Australia.
-
Made to order
Delivery time 4-6 weeks
Cable Vulcanizer - Large (Prototype)
-
Cable Vulcanizers are used to bake the rubber in and around the cable. Essential for all repairs and cable joints/splices.
-
Cable Sizes
Suitable for cable sizes from:
80-130mm diameter cable
-
Designed and built in Australia.
-
Made to order
Delivery time 8-12 weeks
Go/No-Go Test Rings
-
Go/No-Go Rings are used to check that Restrained Electrical Plugs (Mining plugs) meet Australian Standards for flame proof safety.
-
Set of three (3) test gauge rings in hollow bar medium strength high tensile (similar to 1045) in 3 different sizes.
60amp earth sleeve
125/150 earth sleeve
300/425 earth sleeve
-
Designed and built in Australia.
-
Made to order
Delivery time 4-6 weeks
Cable Handler
-
Cable Handlers are used to mechanically move cables around the workshop, off trucks, onto palettes, over to repair workbench etc.
-
4 kW / 415V motor 1:15 reduction with a 35mm output shaft
Lenze Protec Inverter for speed control
Variable Speed controller
Emergency Stop
10m flexible rubber power lead with 20Amp round pin plug
Heavy duty 150mm casters with brakes
-
Suitable for cable sizes from:
10mm-120mm diameter cable
-
Paint colours to be advised
-
Designed and built in Australia.
-
-
Made to order
4-6 weeks
Cable Sheath Tester
-
A Sheath Tester detects pin holes and other damage to the outer sheath of tailing cables.
Unit operates from 0kV to 15kV. Buzzer and light when fault is detected.
-
-
10mm-120mm cable diameter
-
To be advised by client
-
Designed and built in Australia.
-
made to order
8-10 weeks
Cable Drum Reeler - Small
-
-
Specs
• Take drums up to 1300mm wide
• Capacity 2.5 Tonne
• Fork pockets for easy transport
• Plain steel rollers and bearings
• Polyethylene coated drive roller
• Adjustable idle position
for various drum sizes
• Foot switch
• 10m of electrical cable
and 20 Amp plug
• Duplex chain drive
• 1.5 kW motor with reduction gearbox and soft start.
-
Designed and built in Australia.
-
made to order
4-6 weeks
-